If the bathroom only evokes a desire to escape from it as soon as possible, something needs to be changed. If entering the bathroom in the morning, you do not feel comfortable, and your mood deteriorates sharply, do not rush to rebuild it. Most likely, the reason is the flaws in the interior of the bathroom or minor flaws. Building a new bathroom is quite expensive. We will tell you how to fix minor flaws in a couple of days with a help of Australian experts and create a cosy and comfortable space.

Tank Leaking

Cause: There may be several reasons. The tank cap is installed crookedly, the float lever is hooked, the water release button is faulty, or it’s time to replace the gasket.

Solution: Often it is enough to shine a chant of lime in the cistern or at least in the bottom of the cistern where the gasket is. After rinsing, pour strong vinegar into the container and let sit overnight. Check if the gasket is damaged. When replacing the gasket, it is recommended to lightly oil it.

If the water level in the tank is normal, but it still oozes, then the gasket or valve ring is most likely to blame. Change them, just pick up ones that fit your tank. Grab your old parts when you head to the plumbing store.

Dripping Faucet

Cause: Usually the gasket should be changed.

Solution: To change the leather or rubber gasket of the spool, it is necessary to unscrew the clamping nut with a wrench. Then the spindle is unscrewed with a spool. After that, the slot is deepened by cutting it along with the edges of the spool cup with a thin file for metal. In this case, damage to the cup does not affect the operation of the tap. If the spindle ends with a cut axle, the spacer is held back by a nut. To avoid rusting, it must be bronze. The gasket is cut to fit the spool. If there is no special material for a leather pad, you can use an old belt, for a rubber one – a cork. Cutting the rubber plug is made easier by lubricating the knife with soap. A hole in the rubber is pierced with an awl and brought to the required diameter with a round needle file. It is recommended to first make a hole and then cut the workpiece along the spool cup.

Poor Drain Seal

Cause: Incorrectly installed drain or construction defects. If the pop is raised, the seal between the drain and the floor may not be sufficient. This happens when a heated pop is equipped. If there is no good seal between the edges of the drain and the socket, then water flows under the tiles. And if the waterproofing of the priest is insufficient, then the water gradually seeps out to the beams in the floor. In such cases, it is wiser to contact a plumber. Proffesional Canberra plumbers will fix that for you efficiently and in no time.

Solution: The drain should be professionally replaced.

Insufficient Ventilation

Cause: The efficiency of old fans is often not up to date. And this is one of the reasons for the increased dampness in old bathrooms.

Solution: Replace the old fan or install an additional one.

Advice: The fan will be effective only if at the same time provide airflow into the bathroom or kitchen. Perhaps ventilation holes should be made in the bathroom doors.

Ventilation is considered good if 4-0% of the air in the room is renewed per hour. In the bathroom, ventilation should be 10 p / sec. per square meter.

Tiles

Obvious signs: The wall looks uneven, the seams are crumbling, and a dull sound is heard when the wall is tapped.

Cause: Perhaps water has penetrated through the damaged seams behind the tiles. It is possible that water could seep through the crack in the tile.

Solution: It is necessary to remove all the loose tiles, clean out the remaining mortar so that you can put a new one. It is applied with a notched trowel, then a new tile is laid. The new joint mortar must be the same colour and grain size as the old one.

Clogged Fan

Cause: Dust has adhered to the fan, making it difficult to rotate and reducing efficiency

Solution: If the fan is old, it needs to be replaced or cleaned.

Incorrect Floor Slope

Cause: Construction defects or poorly performed internal work.

Solution: The problem can be solved quickly if there is enough space for another layer of tiles. In this case, however, you will have to adjust the height of the drain. And this is where a plumber can help you. The slope in the direction of discharge should be at least 5 mm per meter, which is easy to check with a level and a few wedges.

Cracks between Walls

Cause: Poor stitching.

Solution: Dry the joint and clean out the remaining mortar. Then fill the joint with an elastic acrylic joint sealant. If required, it can be reinforced with a fibreglass strip.

Conclusion

Don’t forget about the aesthetics of the bathroom. It is better to sink the pipes into the walls and additionally cover them with thermal insulation. So you save yourself from the noise of running water and insulate the wall covering from excess moisture. Also, take care of access to all necessary communications – install plumbing hatches to all key water supply points.